EBM 1.9A 700W Centrifugal Fan Inverter D2D160-CE02-11 230V CCC

EBM Centrifugal Fan Inverter Blower Cooling Fan D2D160-CE02-11 230V 1.9A 700W AC

Spare ABB Centrifugal Cooling Fan assembly, complete with motor for ABB ACS800 Inverter Drive.
Type: D2D160-CE02-11 (Was D2D160-BE02-11).
Voltage: 230V/400V .
Power: 700 Watts.

Weight: 14.5kg in carton 60x30x30cm.

Spare for: ACS800-104-0170-3, ACS800-104-0210-3, ACS800-104-0210-5, ACS800-104-0210-7, ACS800-104-0260-3, ACS800-104-0260-5, ACS800-104-0260-7, ACS800-104-0320-3, ACS800-104-0320-5, ACS800-104-0320-7, ACS800-104-0390-3, ACS800-104-0400-5, ACS800-104-0400-7, ACS800-104-0440-7, ACS800-104-0460-5, ACS800-104-0510-3, ACS800-104-0580-7 and ACS800-104-0610-5.

Technical description
Fan size 160 mm
Rotor surface Rotor open, painted black
Impeller material Sheet steel, hot-dip galvanized
Housing material Sheet steel, hot-dip galvanized
Guard grille material Steel, galvanized and coated with whitealuminum plastic (RAL 9006)
Motor suspension Motor vibration-damped on both sides
Direction of rotation Counterclockwise, viewed toward rotor
Degree of protection IP00
Insulation class "F"
Moisture (F) /
Environmental (H)
protection class
F2-1
Installation position Any
Condensation
drainage holes
None, open rotor
Mode S1
Motor bearing Ball bearing
Touch current
according to IEC
60990 (measuringcircuit Fig. 4, TN system) < 0.75 mA
Electrical hookup With plug
Motor protection Thermal overload protector (TOP) with basic insulationwith cable Axial
Protection class I (with customer connection of protective earth)
Conformity with standards EN 60335-1
Approval CCC; CSA C22.2 No. 100; UL 1004-1

The device is exclusively designed as a built-in device for conveying air according to its technical data.

Any other usage above and beyond this does not conform with the intended purpose and constitutes misuse of the device.

Customer equipment must be capable of withstanding the mechanical and thermal stresses that can arise from this product. This applies for the
entire service life of the equipment in which this product is installed.

Intended use also includes
● Using the device only in power systems with grounded neutral (TN/ TT power systems).
● Using the device solely outside of the EU.
● Conveying air at an ambient air pressure between 800 mbar and 1050 mbar.
● Using the device within the permitted ambient temperature range; see
Chapter 3.5 Transport and storage conditions and
Chapter 3.2 Nominal data.
● Operating the device with all protective devices.
● Following the operating instructions.

Improper use
In particular, operating the device in the following ways is prohibited and could be hazardous:
● Operating the device in an unbalanced state, e.g. due to dirt deposits or ice formation.
● Resonant operation, operation with severe vibration. This also includes vibration transmitted to the fan from the customer installation.
● Conveying air that contains abrasive particles.
● Conveying highly corrosive air, e.g. salt spray. Exception: devices designed for salt spray and correspondingly protected.
● Conveying air with high dust content, e.g. suctioning off sawdust.
● Operating the device close to flammable materials or components.
● Operating the device in an explosive atmosphere.
● Using the device as a safety component or to perform safety-related functions.
● Operation with completely or partially disassembled or manipulated protective devices.
● In addition, all applications not listed among the intended uses.

OTHER SUPERIOR PRODUCTS